Training & Events

Available for all NovaTech products and most industry best practices, NovaTech provides expert instruction in our classrooms, online webinars, at technical symposiums, or at your facility.

View the upcoming schedule below:

  • D/3® Hardware Maintenance – 8000 I/O [#S415]

    Aiken, SC Office

    A four-day course designed to give plant personnel the ability to identify malfunctions of the D/3® DCS system. The PCM 4100 and 4200 hardware and 8000 I/O hardware is covered in lecture as well as hands-on experience in troubleshooting and repair.

    July 6, 2015 – July 9, 2015

  • OSHA General Industry 10 Hour Safety Training [#OSHA]

    Owings Mills, MD Office

    This two-day course provides a general industry employee understanding of their rights under the Federal Law 29 CFR 1910. The course comprises of the mandatory hour each dedication to the OSH Act, Walking Working Surfaces, Egress, and Electrical Safety.

    July 7, 2015 – July 8, 2015

  • D/3® User [#L452]

    Denham Springs, LA

    A ten-day entry level course using D/3® software explaining the architecture and configuration of the D/3®, operation and control of the D/3® Operator Console, and the configuration of the Continuous Control database.

    July 13, 2015 – July 24, 2015

  • Practical Active Directory for D/3® [#M494]

    Owings Mills, MD Office

    A five day course designed especially for those D/3® users who operate their DCS systems in an Active Directory. As such, this course focuses on practical Active Directory configurations for local, wide and corporate networks.

    July 20, 2015 – July 24, 2015

  • FlexBatch® Production Operator [#S466]

    AIken, SC Office

    A two-day course covering the use of FlexBatch® to create and execute campaigns and batches. Details of the Production Displays provide students with interactive tools to create, monitor or modify the status of active batches.

    July 27, 2015 – July 28, 2015

  • FlexBatch® D/3® Recipe Developer [#S467]

    Aiken, SC Office

    A three-day course covering the use of FlexBatch® Production Displays to create, execute and monitor campaigns and batches. Students will be able to use the Configuration Management software to create and modify new master recipes.

    July 27, 2015 – July 29, 2015

  • FlexBatch® D/3® Control Engineer [#S468]

    AIken, SC Office

    A five-day course detailing the use of FlexBatch® with a D/3® Distributed Control System. Details on the various Production Displays provide the user with tools to create and monitor campaigns and batches.

    July 27, 2015 – July 31, 2015

  • Windows Security for D/3® [#M435]

    Owings Mills, MD Office

    A five-day course is “packed” with the latest security information and documentation you need to learn the dangers and defenses you can use to evaluate and support the security of a Microsoft Windows system configured for D/3® operation.

    August 3, 2015 – August 7, 2015

  • D/3® Application Design Techniques [#M441]

    Owings Mills, MD

    A five-day course covering best practices of D/3® Application Design and Implementation. Two commonly used application techniques provide case studies of how to design controls that behave in predictable manor under all process conditions.

    August 10, 2015 – August 14, 2015

  • D/3® System Management [#S450]

    AIken, SC Office

    A three-day hands-on course designed to show all of the new features of the D/3® system on the Windows platform.

    August 11, 2015 – August 13, 2015

  • D/3® SABL® [#S456]

    Aiken Training Office

    A five-day course, using D/3® software, covering the steps involved in developing and using the SABL® package.

    August 17, 2015 – August 21, 2015

  • D/3® Hardware Maintenance – 8000 I/O [#L415]

    Denham Springs, LA Office

    A four-day course designed to give plant personnel the ability to identify malfunctions of the D/3® DCS system. The PCM 4100 and 4200 hardware and 8000 I/O hardware is covered in lecture as well as hands-on experience in troubleshooting and repair.

    August 25, 2015 – August 28, 2015

  • D/3® User [#S452]

    Aiken Training Office

    A ten-day entry level course using D/3® software explaining the architecture and configuration of the D/3®, operation and control of the D/3® Operator Console, and the configuration of the Continuous Control Database.

    September 14, 2015 – September 25, 2015

  • Practical Active Directory for D/3® [#L494]

    Denham Springs, LA Office

    A five day course designed especially for those D/3® users who operate their DCS systems in an Active Directory. As such, this course focuses on practical Active Directory configurations for local, wide and corporate networks.

    September 14, 2015 – September 18, 2015

  • OrionLX / OrionLXm Automation Platform [#K700]

    Lenexa, KS Training Office

    A one and a half-day course to provide instruction in the specification, configuration, application, and real-time monitoring of the OrionLX / LXm automation processor.  Students will be introduced to OrionLX / LXm hardware and firmware options and their various uses and applications. 

    September 22, 2015 – September 23, 2015

  • FlexBatch® Production Operator [#L466]

    Denham Springs, LA Office

    A two-day course covering the use of FlexBatch® to create and execute campaigns and batches. Details of the Production Displays provide students with interactive tools to create, monitor or modify the status of active batches.

    October 5, 2015 – October 6, 2015

  • FlexBatch® D/3® Recipe Developer [#L467]

    Denham Springs, LA Office

    A three-day course covering the use of FlexBatch® Production Displays to create, execute and monitor campaigns and batches. Students will be able to use the Configuration Management software to create and modify new master recipes.

    October 5, 2015 – October 7, 2015

  • FlexBatch® D/3® Control Engineer [#L468]

    Denham Springs Training Office

    A five-day course detailing the use of FlexBatch® with a D/3® Distributed Control System. Details on the various Production Displays provide the user with tools to create and monitor campaigns and batches. New recipes are developed and then validated through batch execution.

    October 5, 2015 – October 9, 2015

  • [Microsoft Series] – D/3® Network Support [#L429]

    Denham Springs, LA Office

    Learn Network Essentials, proper configuration, and troubleshooting with network monitoring and troubleshooting tools in order to support a D/3® environment.

    October 12, 2015 – October 14, 2015

  • D/3® Hardware Maintenance – 8000 I/O [#S415]

    Aiken, SC Office

    A four-day course designed to give plant personnel the ability to identify malfunctions of the D/3® DCS system. The PCM 4100 and 4200 hardware and 8000 I/O hardware is covered in lecture as well as hands-on experience in troubleshooting and repair.

    October 13, 2015 – October 16, 2015

  • D/3® Network Management [#L427]

    Denham Springs, LA Office

    A two-day course designed especially for the D/3® users. This industrial networking environment course presents modules on industrial hubs, KVM(s), switches, routers, VPN(s) and firewalls with a focus on MTBF (mean time between failure).

    October 15, 2015 – October 16, 2015

  • D/3® SABL® [#M456]

    Owings Mills Training Office

    A five-day course, using D/3® software, covering the steps involved in developing and using the SABL® package. Students will develop the Sequence Database and SABL® programs necessary to manipulate and interact with the continuous database and operator console.

    October 19, 2015 – October 23, 2015

  • D/3® Application Design Techniques [#L441]

    Denham Springs Training Office

    A five-day course covering best practices of D/3® Application Design and Implementation. Two commonly used application techniques provide case studies of how to design controls that behave in predictable manor under all process conditions.

    October 26, 2015 – October 30, 2015

  • D/3® 8000 I/O Configuration [#M413]

    Owings Mills, MD Office

    A two-day course explaining the configuration and maintenance of the EthernetMPC2 (Multi Protocol Controller) Interface Card and 8000 I/O hardware. Use software tools to build databases and perform 8000 I/O diagnostics from operator consoles and D/3 utilities.

    October 26, 2015 – October 27, 2015

  • D/3® Alarm Management [#M492]

    Owings Mills, MD

    A two-day course using D/3® software explaining the operation and control of the D/3® alarm systems.

    October 28, 2015 – October 29, 2015

  • D/3® User [#S452]

    Aiken Training Office

    A ten-day entry level course using D/3® software explaining the architecture and configuration of the D/3®, operation and control of the D/3® Operator Console, and the configuration of the Continuous Control Database.

    November 2, 2015 – November 13, 2015

  • Windows Security for D/3® [#M435]

    Owings Mills, MD Office

    A five-day course is “packed” with the latest security information and documentation you need to learn the dangers and defenses you can use to evaluate and support the security of a Microsoft Windows system configured for D/3® operation.

    November 2, 2015 – November 6, 2015

  • D/3® 8000 I/O Configuration [#S413]

    Aiken, SC Office

    A two-day course explaining the configuration and maintenance of the EthernetMPC2 (Multi Protocol Controller) Interface Card and 8000 I/O hardware.

    November 16, 2015 – November 17, 2015

  • D/3® System Management [#S450]

    AIken, SC Office

    A three-day hands-on course designed to show all of the new features of the D/3® system on the Windows platform.

    November 18, 2015 – November 20, 2015

  • OrionLX / OrionLXm Automation Platform [#K700]

    Lenexa, KS Training Office

    A one and a half-day course to provide instruction in the specification, configuration, application, and real-time monitoring of the OrionLX / LXm automation processor.  Students will be introduced to OrionLX / LXm hardware and firmware options and their various uses and applications. 

    December 8, 2015 – December 9, 2015

  • D/3® SABL® [#S456]

    Aiken Training Office

    A five-day course, using D/3® software, covering the steps involved in developing and using the SABL® package.

    December 14, 2015 – December 18, 2015

  • OSHA General Industry 10 Hour Safety Training [#OSHA]

    Denham Springs, LA Office

    This two-day course provides a general industry employee understanding of their rights under the Federal Law 29 CFR 1910. The course comprises of the mandatory hour each dedication to the OSH Act, Walking Working Surfaces, Egress, and Electrical Safety.

    December 15, 2015 – December 16, 2015

  • D/3® 8000 I/O Configuration [#S413]

    Aiken, SC Office

    A two-day course explaining the configuration and maintenance of the EthernetMPC2 (Multi Protocol Controller) Interface Card and 8000 I/O hardware.

    January 4, 2016 – January 5, 2016

  • D/3® Alarm Management [#S492]

    Aiken, SC Office

    A two-day course using D/3® software explaining the operation and control of the D/3® alarm systems.

    January 6, 2016 – January 7, 2016

  • D/3® User [#M452]

    Owings Mills, MD

    A ten-day entry level course using D/3® software explaining the architecture and configuration of the D/3®, operation and control of the D/3® Operator Console, and the configuration of the Continuous Control database.

    January 11, 2016 – January 22, 2016

  • Practical Active Directory for D/3® [#S494]

    Aiken, SC Office

    A five day course designed especially for those D/3® users who operate their DCS systems in an Active Directory. As such, this course focuses on practical Active Directory configurations for local, wide and corporate networks.

    January 25, 2016 – January 29, 2016

  • D/3® Application Design Techniques [#S441]

    Aiken Training Office

    A five-day course covering best practices of D/3® Application Design and Implementation. Two commonly used application techniques provide case studies of how to design controls that behave in predictable manor under all process conditions.

    February 1, 2016 – February 5, 2016

  • [Microsoft Series] – D/3® Network Support [#S429]

    Aiken, SC Office

    Learn Network Essentials, proper configuration, and troubleshooting with network monitoring and troubleshooting tools in order to support a D/3® environment.

    February 15, 2016 – February 17, 2016

  • D/3® SABL® [#L456]

    Denham Springs, LA

    A five-day course, using D/3® software, covering the steps involved in developing and using the SABL® package.

    February 15, 2016 – February 19, 2016

  • D/3® Network Management [#S427]

    Aiken, SC Office

    A two-day course designed especially for the D/3® users. This industrial networking environment course presents modules on industrial hubs, KVM(s), switches, routers, VPN(s) and firewalls with a focus on MTBF (mean time between failure).

    February 18, 2016 – February 19, 2016

  • D/3® Hardware Maintenance – 8000 I/O [#S415]

    Aiken, SC Office

    A four-day course designed to give plant personnel the ability to identify malfunctions of the D/3® DCS system. The PCM 4100 and 4200 hardware and 8000 I/O hardware is covered in lecture as well as hands-on experience in troubleshooting and repair.

    March 7, 2016 – March 10, 2016

  • Windows Security for D/3® [#S435]

    Aiken, SC Office

    A five-day course is “packed” with the latest security information and documentation you need to learn the dangers and defenses you can use to evaluate and support the security of a Microsoft Windows system configured for D/3® operation.

    March 14, 2016 – March 18, 2016

  • D/3® 8000 I/O Configuration [#L413]

    Denham Springs, LA Office

    A two-day course explaining the configuration and maintenance of the EthernetMPC2 (Multi Protocol Controller) Interface Card and 8000 I/O hardware.

    March 21, 2016 – March 22, 2016

  • D/3® Alarm Management [#L492]

    Denham Springs, LA

    A two-day course using D/3® software explaining the operation and control of the D/3® alarm systems.

    March 23, 2016 – March 24, 2016